EVAL-AD7328CB【PDF 15/36 页】8-Channel, Software-Selectable True Bipo

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录362800

11页 12页 13页 14页 [15页]16页 17页 18页 19页

AD7328

THEORY OF OPERATION

CIRCUIT INFORMATION

The AD7328 is a fast, 8-channel, 12-bit plus sign, bipolar input,

serial A/D converter. The AD7328 can accept bipolar input

ranges that include ±10 V, ±5 V, and ±2.5 V; it can also accept a

0 V to +10 V unipolar input range. A different analog input

range can be programmed on each analog input channel via the

on-chip registers. The AD7328 has a high speed serial interface

that can operate at throughput rates up to 1 MSPS.

Rev. A | Page 15 of 36

The AD7328 requires V

and V

dual supplies for the high

voltage analog input structures. These supplies must be equal

to or greater than the analog input range. See Table 6 for the

requirements of these supplies for each analog input range. The

AD7328 requires a low voltage 2.7 V to 5.25 V V

supply to

power the ADC core.

Table 6. Reference and Supply Requirements for Each

Analog Input Range

Selected Analog

Input Range (V)

±10

Reference

Voltage (V)

2.5

3.0

2.5

3.0

2.5

3.0

2.5

3.0

Full-Scale

Input

Range (V)

±10

±12

±5

±6

±2.5

±3

0 to +10

0 to +12

(V)

3/5

Minimum

(V)

±10

±12

±5

±6

±5

+10/AGND

+12/AGND

±5

±2.5

0 to 10

To meet the specified performance specifications when the

AD7328 is configured with the minimum V

and V

supplies

for a chosen analog input range, the throughput rate should be

decreased from the maximum throughput range (see the

Typical Performance Characteristics section). Figure 18 and

Figure 19 show the change in INL and DNL as the V

and V

voltages are varied. When operating at the maximum through-

put rate, as the V

and V

supply voltages are reduced, the INL

and DNL error increases. However, as the throughput rate is

reduced with the minimum V

and V

supplies, the INL and

DNL error is reduced.

Figure 31 shows the change in THD as the V

and V

supplies

are reduced. At the maximum throughput rate, the THD

degrades significantly as V

and V

are reduced. It is therefore

necessary to reduce the throughput rate when using minimum

and V

supplies so that there is less degradation of THD

and the specified performance can be maintained. The

degradation is due to an increase in the on resistance of the

input multiplexer when the V

and V

supplies are reduced.

The analog inputs can be configured as eight single-ended

inputs, four true differential input pairs, four pseudo differential

inputs, or seven pseudo differential inputs. Selection can be

made by programming the mode bits, Mode 0 and Mode 1, in

the control register.

The serial clock input accesses data from the part and provides

the clock source for the successive approximation ADC. The

AD7328 has an on-chip 2.5 V reference. However, the AD7328

can also work with an external reference. On power-up, the

external reference operation is the default option. If the internal

reference is the preferred option, the user must write to the

reference bit in the control register to select the internal reference

operation.

The AD7328 also features power-down options to allow power

savings between conversions. The power-down modes are

selected by programming the on-chip control register as

described in the Modes of Operation section.

CONVERTER OPERATION

The AD7328 is a successive approximation analog-to-digital

converter built around two capacitive DACs. Figure 23 and

Figure 24 show simplified schematics of the ADC in single-

ended mode during the acquisition and conversion phases,

respectively. Figure 25 and Figure 26 show simplified schematics

of the ADC in differential mode during acquisition and conversion

phases, respectively.

The ADC is composed of control logic, a SAR, and capacitive

DACs. In Figure 23 (the acquisition phase), SW2 is closed and

SW1 is in Position A, the comparator is held in a balanced con-

dition, and the sampling capacitor array acquires the signal on

the input.

CAPACITIVE

DAC

CONTROL

LOGIC

COMPARATOR

AGND

SW2

SW1

Figure 23. ADC Acquisition Phase (Single Ended)

When the ADC starts a conversion (Figure 24), SW2 opens and

SW1 moves to Position B, causing the comparator to become

unbalanced. The control logic and the charge redistribution

DAC are used to add and subtract fixed amounts of charge from

the capacitive DAC to bring the comparator back into a balanced

condition. When the comparator is rebalanced, the conversion

is complete. The control logic generates the ADC output code.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式